PIPE-MIC II
(Pronounced "PIPE MIKE")
Measure pipe inverts and sizes fast, easy & accurate
* Measurements are more accurate because you are measuring
with a vertical plumb rod.
* Made for Crain 25' SVR, USL rods and our new double sided
PIPE-MIC II rod.
* Made of lightweight (two pounds) non rusting aircraft aluminium.
* No tools needed to attach to rod.
* Slides on and off in seconds.
* New round foot design slices through material at bottom of pipe
and insures accurate invert and pipe diameter measurement.
with a vertical plumb rod.
* Made for Crain 25' SVR, USL rods and our new double sided
PIPE-MIC II rod.
* Made of lightweight (two pounds) non rusting aircraft aluminium.
* No tools needed to attach to rod.
* Slides on and off in seconds.
* New round foot design slices through material at bottom of pipe
and insures accurate invert and pipe diameter measurement.
By pulling a pin in just seconds you can go from zero to 1 ft. vertical offset for clearance under rod.
New Double Sided PIPE-MIC II Rod
* Made exclusively for the PIPE-MIC II
* Reduces multiple setups when using a Total Station or Auto level.
* Printed in tenths on front & back of rod.
Part # 172510
PIPE-MIC II Double Sided Rod 25' 10th
List $246.00
* Made exclusively for the PIPE-MIC II
* Reduces multiple setups when using a Total Station or Auto level.
* Printed in tenths on front & back of rod.
Part # 172510
PIPE-MIC II Double Sided Rod 25' 10th
List $246.00
To use:
* You can direct read the depth of the invert when the pin is set at "zero offset" on the PIPE-MICII.
* If you need clearance under rod to measurement an invert move the pin to "1' vertical offset hole"
* If you need clearance under rod and a pipe that is hard to reach you can add a 1 ft. extension.
(1 ft. extension sold separately) Move pin to " 1' vertical offsetw/ 1' extension" hole.
To size a pipe:
The foot is 0.33 or 4". Take the reading from the rim, pull up and take reading plus 0.33 and that is your pipe size.
* You can direct read the depth of the invert when the pin is set at "zero offset" on the PIPE-MICII.
* If you need clearance under rod to measurement an invert move the pin to "1' vertical offset hole"
* If you need clearance under rod and a pipe that is hard to reach you can add a 1 ft. extension.
(1 ft. extension sold separately) Move pin to " 1' vertical offsetw/ 1' extension" hole.
To size a pipe:
The foot is 0.33 or 4". Take the reading from the rim, pull up and take reading plus 0.33 and that is your pipe size.
Example:
4" Pipe = 0.00 movement
6" Pipe = 0.17
8" Pipe = 0.33
10" Pipe = 0.50
12" Pipe = 0.67
4" Pipe = 0.00 movement
6" Pipe = 0.17
8" Pipe = 0.33
10" Pipe = 0.50
12" Pipe = 0.67
PIPE-MIC Extension
Made in the USA
Part # 1702PM2
List price $200.00
List price $200.00
Testimonial on the PipeMic II-
"We have been using the Pipe-Mic II for over 4 years and have found it to be an invaluable tool. We initially purchased it for a contract with a local sanitation district. Accurate invert elevations and pipe sizes were needed for sewer force mains, trunk lines, secondary lines as well as storm drain lines, catch basins and other structures. All of these measurements were obtained using the Pipe-Mic, including manhole invert elevations that exceeded 25 feet; it would have been impossible to get accurate pipe sizes and inverts at the depth using the "old method". The Pipe-Mic has not only increased the accuracy of our readings but allowed us to obtain those readings more quickly and safely. Thank you for such a wonderful product." Jason Moore- Proactive Engineering Consultants, Inc.
"We have been using the Pipe-Mic II for over 4 years and have found it to be an invaluable tool. We initially purchased it for a contract with a local sanitation district. Accurate invert elevations and pipe sizes were needed for sewer force mains, trunk lines, secondary lines as well as storm drain lines, catch basins and other structures. All of these measurements were obtained using the Pipe-Mic, including manhole invert elevations that exceeded 25 feet; it would have been impossible to get accurate pipe sizes and inverts at the depth using the "old method". The Pipe-Mic has not only increased the accuracy of our readings but allowed us to obtain those readings more quickly and safely. Thank you for such a wonderful product." Jason Moore- Proactive Engineering Consultants, Inc.